全自動聚乙烯壓痕硬度測定儀

SLYQ-96A/3路

一、滿足標準：

GB/T 23257-2009 埋地鋼質管道聚乙烯防腐層

二、全自動聚乙烯壓痕硬度測定儀概述：

本儀器主要測試聚乙烯在一定的溫度環境和恒定的壓力下經過一定的時間后的壓痕深度。

本儀器是國內自動化程度zui高，zui的測試聚乙烯壓痕硬度的測試儀器，由于做的時間比較長，試驗人員只需要在試驗前設定好參數后，會自動根據設置的實驗條件進行加溫，并保持恒溫，能夠自動加載，并自動采集結果、計算平均數值。實驗完成后有報警提示，報警時間長短可以設定！

    三、全自動聚乙烯壓痕硬度測定儀產品特點：

1、本儀器核心控制部分通過7寸觸摸屏設置參數并控制。

2、本儀器變形采集利用國內的微型位移傳感器技術，淘汰了利用數字千分表采集位移精度低、易壞及需要更換電池等缺陷

3、設置好參數后，點開始實驗后自動加載，實驗結束后自動計算結果，同時壓頭自動復位到初始位置進行下次實驗

1. 同時可以做三路實驗，也可以單獨進行一路或二路
2. 本儀器帶有微型打印機，可以對試驗結果進行打印，并自動計算平均值。
3. 測試環境溫度為：室溫-100度，溫度可設定
4. 具有報警提示，實驗完成后根據設定的報警時間進行報警。

四、全自動聚乙烯壓痕硬度測定儀技術參數：

1、試驗負荷：10MP（25N）

2、壓頭直徑：Ф1.8mm

3、控溫精度：±0.5度

4、壓痕深度指示zui小分度值：0.01mm

5、耐壓時間：可以設定

6、主機變形量：≤0.04mm

7、測量范圍有效值：可以設定

8、允許zui大試樣厚度：50MM

五、全自動聚乙烯壓痕硬度測定儀主要配置及附件：

　    1、主    機：        一臺

　    2、主機壓頭￠1.8mm：三個

      3、微型打印機：      一臺

      4、自動加載裝置：    三套

      5、位移傳感器：      三個

      6、恒溫加熱裝置：    一套

      7、使用說明書：      一份

      8、德國西門子PLC：  一個

      9、德國西門子采集模塊：一個

      10、寸彩色觸摸屏：  一個

英文資料簡介如下：

 Full automatic polyethylene indentation hardness tester

SLYQ-96A/3 Road

One, meet the standards:

GB/T 23257-2009 polyethylene coating for buried steel pipeline

=====================================

Two, automatic determination instrument of polyethylene indentation hardness:

The instrument is mainly test of polyethylene in a definite temperature environment and the constant pressure after indentation depth after a certain time.

This instrument is the highest degree of automation, test instrument most leading testing polyethylene indentation hardness, as a result of the relatively long time, test personnel only need to set parameters in the test before and after, will automatically according to the experimental conditions set for heating, and keep constant temperature, capable of automatic loading, automatic acquisition and calculation results, the average numerical. After completion of the experiment has alarm, alarm time can be set!

===============================

Three, automatic indentation hardness tester product features of polyethylene:

1, the instrument is the core control part through a 7 Inch Touch screen set up parameters and control.

2, the collection and utilization of micro displacement sensor deformation technology leading, eliminated using digital micrometer acquisition displacement precision is low, easily broken and the need to replace the battery and other defects

3, after parameter setting, some began to automatic loading experiment, automatic calculation results after the experiment, at the same time indenter automatic reset to the initial position for the next experiment

4, at the same time can do three experiments, can also be a road or two separate

5, the instrument with a micro printer, you can print the test results, and automatic calculation of average value.

6, test environment temperature: room temperature -100 degrees, the temperature can be set

7, an alarming, after completion of the experiment according to the set alarm time and alarm.

==========================================

Tester technical parameters four, full automatic polyethylene indentation hardness:

1, the test load (25N): 10MP

2, the pressure head diameter: 1.8mm

3, temperature control precision is ± 0.5 degrees:

4, the indentation depth indicates the minimum scale value: 0.01mm

5, pressure time: you can set

6, the host deformation: ≤ 0.04mm

7, the effective value measurement range: can be set

8, to allow maximum thickness: 50MM

==============================

Five, automatic indentation hardness tester of polyethylene main configuration and accessories:

1, the main machine: a

2, the host head - 1.8mm: three

3, micro printer: a

4, automatic loading device: three sets

5, the displacement sensor: Three

6, a constant temperature heating device: a

7, the use of manual: a

8, Germany Siemens PLC: a

9, Germany Siemens acquisition module: a

10, inch color touch screen: a